HELIX M ONE Car Audio Mono Sub Subwoofer Amplifier 600w RMS at 1 ohm

Small, efficient and uncompromisingly stable - the M ONE is a highly compact monoblock for subwoofer applications. Designed from latest Class D technology this tiny amp can easily control speakers with 1 Ohm impedance. Its current capability makes the M ONE a perfect partner for 2 x 2 Ohms subwoofers, where both voice coils are connected in parallel.

In addition a comprehensive and stunningly practical feature set leaves nothing to be desired. Last but not least installation will be a no-brainer due to the minimal dimensions.

Small footprint Class D amplifier with high output power of 600 Watts RMS @ 1 Ohm for easiest combination with all 2 x 2 Ohms subwoofers connected in parallelStart-Stop capability down to 6V supply voltageSmart highlevel input with ADEP circuit (Advanced Diagnostics Error Protection) and Auto Turn-On functionIntegrated, active crossover with lowpass,bass boost, subsonic and phase controlExtremely stable output stage with high-current power transistors and 1 Ohm stabilityBass remote control for volume adjustmentSMD (Surface Mounted Device) manufacturing technology combines minimum space requirement with maximum reliabilityExclusive, extremely compact and clean design with illuminated HELIX-logo and low heat dissipation thanks to extraordinary efficiency

Special features:

Smart highlevel inputThe latest generation of OE car radios incorporates sophisticated possibilities of diagnosing the connected speakers. If a common amplifier will be hooked up failure messages and loss of specific features (e.g. fader function) quite often appear - but not with the M ONE.The new ADEP circuit (Advanced Diagnostics Error Protection) avoids all these problems without loading the speaker outputs of the OE radio during high volumes unnecessarily.

Start-Stop capabilityThe switched power supply of the HELIX M ONE assures operation even if the battery's voltage drops down to 6 Volts during engine crank.

Output power RMS / max. - @ 4 Ohms 1 x 240 / 480 Watts- @ 2 Ohms 1 x 410 / 820 Watts- @ 1 Ohm 1 x 600 / 1,200 Watts- bridged @ 4 Ohms -- bridged @ 2 Ohms -Amplifier technology Class DInputs 2 x RCA / Cinch2 x Highlevel speaker input1 x Remote In1 x Remote control inputInput sensitivity RCA / Cinch 0.5 - 6 VoltsHighlevel 1.1 - 13 VoltsInput impedance RCA / Cinch 20 kOhmsInput impedance highlevel 13 OhmsOutputs 1 x Speaker outputOutput voltage RCA / Cinch - Signal converter for digital input - Frequency response 10 Hz - 250 HzBass boost 0 - 12 dB / 25 - 75 HzHighpass - Lowpass 50 Hz - 250 Hz adjustableBandpass 10 Hz - 250 Hz adjustableSubsonic 10 Hz - 50 Hz adjustablePhase 0 - 180° adjustableSlope high- / lowpass - Slope subsonic / lowpass 12 / 24 dB/Oct.Signal-to-noise ratio digital input - Signal-to-noise ratio analog input 95 dB (A-weighted)Distortion (THD) 0.20 %Damping factor 100Operating voltage 10.5 - 16 Volts (max. 5 sec. down to 6 Volts)Idle current 650 mAFuse 2 x 35 A Maxi-fuse (APX)Additional features Active, adjustable crossover, bass boost, phase shift, Start-Stop capability, highlevel input with automatic turn on function and Advanced Diagnostics Error Protection (ADEP), bass volume cable remote control Dimensions (H x W x D) 50 x 230 x 154 mm / 2.00 x 9.06 x 6.06"